Program Files/Common Files/Somagic/SmiUsbGrabber3C/xp/SmiUsbGrabber3C.sys To update it in the future, use "git pull". Go to your home directory and create a folder called easycap To determine that: plug in the Eas圜AP, run "lsusb", and verify "1 Somagic, Inc."Įas圜AP USB 2.0 Video Adapter with Audio or Eas圜AP002 4-Channel USB 2.0 DVR installation CD-ROM. Sudo apt-get install wine git build-essential libusb-1.0-0-dev libgcrypt11-dev mplayer usbutils On Ubuntu, that can all be installed by running the following command as root: GNU/Linux with the following programs and libraries installed: wine, git, make, gcc, libusb-1.0-0 (and development headers), libgcrypt11 (and development headers), mplayer, lsusb (optional). The benefit of the kernel module is that it gives you a /dev/videoX device and runs with V4L2. The current state of the drivers provides you with two options: the userspace programs and the kernel module (buggy?). When you plug it in and do an "lsusb" you should see:Īll the work on this has been done by the guys over on:īut I thought I would replicate it here following my efforts (so this is not my own work!). smi2021 1-7:1.This info is for the Somagic variant of the easycap DC60 Video convertor. usb 1-7: New USB device found, idVendor=1c88, idProduct=003c usb 1-7: new high-speed USB device number 11 using ehci-pci usb 1-7: USB disconnect, device number 10 usbcore: registered new interface driver smi2021 usb 1-7: Direct firmware load failed with error -2 usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-7: New USB device found, idVendor=1c88, idProduct=0007 The firmware is sourced from the CD and installed into /lib/firmware usb 1-7: new high-speed USB device number 10 using ehci-pci The end result then is lsusb shows as follows: 1c88:003c Somagic, Inc. These files can then be copied from drivers/media/i2c/saa71105.ko and drivers/media/usb/smi2021/smi2021.ko to /lib/modules/linux…./kernel/drivers/… and depmod -a run to update dependencies. In this version, for some reason or another, drivers/media/usb/smi2021.h needed the following line to be included as well: #include Wget -no-check-certificate -O smi2021v3.patchĮdit Makefile to set EXTRAVERSION as follows to ensure module symbol match EXTRAVERSION = 86_64 Then setting up and patching: cd ~/rpmbuild To make everything match, you may also want to install a matching, updated kernel yum install kernel kernel-headers Rpmbuild -bp -target=$(uname -m) kernel.spec The Process Preparation sudo yum install rpmdevtools yum-utils The steps that follow combine the instructions from both the project page as well as teh Fedora wiki: SMI Grabber (Eas圜AP DC60+ clone) (no firmware) ĭrivers *are* available from a the easycap-somagic-linux project but require compilation. This device turned out to identify as follows in Fedora Core 19 with kernel 3.13.86_64 and was not available as a device in V4L New USB device found, idVendor=1c88, idProduct=0007 Needing a video display solution for streamed video from the Cobra, I obtained a Eas圜AP USB 2.0 Audio/Video Capture off DX.com.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |